Welding

Dimide Welding Clamps Review – Impact Wrench Ready


Welding Clamps

Build Quality
Feature Set
Performance
Value
Final Thoughts

Dimide welding clamps deliver more than 7,000 pounds of clamping force, safe to use with an impact wrench, and they are made in the USA.

Overall Score 4.6 Pro Review

These new Dimide welding clamps are rated for use with an impact wrench, up to 400 ft-lbs. Dimide welding clamps are made in the USA and they deliver more than 7,000 pounds of clamping force. The Dimide #5 is a 5-inch clamp and sells for $99. Also available is the Dimide #8 clamp, which is an 8-inch clamp and sells for $129. Dimide is also taking early orders for their soon-to-be-released 12-inch clamp, with a price of $239 each.

We used our Milwaukee mid-torque impact wrench with the Dimide welding clamps. The ~400 ft-lbs of max force from the mid-torque was a perfect fit for using with these clamps. Using an impact provides more clamping force and also aids in speeding up repetitive clamping.

Dimide Welding Clamps Features

1/2" Hex Clamping RodThese Dimide clamps provide plenty of clamping load to keep your work secure, whether you’re welding, grinding, drilling, or sanding. The #5 Dimide clamp delivers 7,000 pounds of clamping load, and the #8 clamp provides more than 7,400 pounds of force. Try to match this with your old clamps. In addition to the increased clamping load, these Dimide clamps are also much faster, especially when used with an impact wrench. With a 13mm or 1/2″ socket, the clamps can go from fully open to fully closed in just a couple seconds. You not only save time, but it’s also less fatigue and work on your hands, cranking all those clamps down.

The jaws and main threaded clamping rod are made of copper to keep off as much welding spatter as possible. The copper jaws are square cubes, allowing the user to rotate the cube for the best hold. Two sides are flat for clamping any flat surfaces. Another side has a lateral v-groove down the middle which aids in clamping pipe, vertical flat-bar, or angle-iron. And yet another side has two v-grooves at 45-degree angles, crossing one another like an x-y axis (similar to an “X”).

Finally, the Dimide welding clamps are all designed and made in the USA. These clamps are rugged, fast and provide tons of clamping force – literally. If you routinely need clamps for securing work, such as grinding and welding, then we definitely recommend the Dimide welding clamps.

Click here for more information on the Dimide Clamps.

4
Leave a Reply

avatar
1 Comment threads
3 Thread replies
0 Followers
 
Most reacted comment
Hottest comment thread
2 Comment authors
EmmetDavid S Recent comment authors
  Subscribe  
newest oldest most voted
Notify of
David S
Guest
David S

I see two issues with the way you’re tightening the clamp with your impact wrench. First you state in both the video and the text that it has a 1/2″ head on the end opposite the knob, then you state that you can use a 1/2″ or 13 mm socket. In the video you do use a 13 mm socket to tighten it with that socket being a chrome socket. There is enough difference between 1/2″ and 13 mm that I wouldn’t be using a 13 mm socket to tighten a 1/2: jack screw or anything else. That is unless… Read more »

Emmet
Guest

Hi David, Emmet with Dimide here. The clamp is designed for use with a 1/2″ hex on only the male hex which is hardened high tensile strength steel and is designed specifically to handle the abuse of a 400 ft-lbs impact wrench (any mid-range impact). The female hex where the knob is inserted will deform under impact wrench loading due to the hammer action. Should the screw fail under proper use, the clamps come with a 2-year warranty to cover such damage.

David S
Guest
David S

Thanks for your input Emmet. I noticed that you didn’t say it’s designed for a 1/2″ OR 13 MM socket as he did in his review of the clamps. That’s what I was pointing out, that 1/2″ and 13 MM are different sizes and shouldn’t be interchanged when tightening something such as this that can withstand 400 ft-lbs of tightening torque, let alone using a socket that isn’t approved for impact use.

Emmet
Guest

Hi David, yes you are right. The extra room that a 13 mm would have on the 1/2″ hex would cause increased wear on both the clamp hex and the socket you’re using to drive the clamp. Thanks for pointing this out!